How to Fix a Broken Pipe Inside a Wall

The broken pipes can spell a lot of problems for any homeowner. However, they are easily repaired and the reason for their damage can be prevented. With the right tools, knowledge and knowledge of your home’s plans and blueprint, you can also accomplish the task. Here is How to Fix a Broken Pipe Inside a Wall.

What Causes Pipes to Break?

Extremely cold temperatures are the main reason behind ruptured pipes. The water inside the pipes to expand, and eventually get near freezing. If the pressure rises to a certain degree it is possible that the pipe’s structure becomes damaged. This is usually the case when the temperature drops to the minus -6 degree C.

How Do You Know if a Pipe Has Burst

The indicators of a ruptured pipe may go unnoticed or appear all everywhere, based on the location and severity of rupture. The warning signs always include water.

  • Flooding. The most obvious indication is when you see pools of water over the flooring, or if the walls are damp, and you can see the water meter spin like mad, then you’ve got flooding.
  • Bubbled walls. When the water leak isn’t so obvious, you will observe bubbles developing beneath wallpapers or paint of your walls.
  • Mold. Another indicator of excessive moisture. There are homes that suffer from this regardless, but if your having problems with mold that you haven’t seen in awhile there could be a reason. It could be an issue with your pipe.
  • Patches of vegetation. If a pipe is bursting outside your home and surrounding your yard, it could be gushing over your lawn. If you notice patches of green grass most likely an issue with the pipe.

How to Locate the Broken Pipe

If ice builds up in the pipes of your home, it does not necessarily cause harm to the area in which it was formed. Sometimes the only thing ice causes is an obstruction, causing pressure that explodes in the most vulnerable area that could be located in another location. This is why it’s crucial to pinpoint the location where the blockage occurred.

  • Check the signs of water damage. Examine your floors, walls, ceiling, basement , and take note of the place where the damage signs are the most obvious. It’s likely that the leak is there, even though it’s not required. Most often, water pools on another area.
  • Find exposed basement pipes for mold and corrosion. The presence of moisture, corrosion, mold or wood that is rotten indicate the need for leak repair close to. The pipe that is damaged is most likely to be located in the walls behind it.
  • Try to smell the scent of the smell of sewage. You don’t have to attempt this one. Sewage smell is a sign that you not only have a damaged pipe, but it’s also an sewage pipe. In this case the situation can become quite messy. It is recommended to immediately contact a professional because they have the right equipment to handle these situations. In addition, the poisonous gas that comes from sewer pipes can cause a lot of explosions.

How to prevent pipes from freezing

If you are serious about the value of your home it is essential to pay attention at the condition of your plumbing. If you do not want to contact a plumber every winter, it is important to be proactive against cold temperatures.

  • Insulate all pipes that are water-related. Insulation is the first step to avoid freezing however it’s not all you must perform, since it reduces the chilling air.
  • Utilize heaters. If you had to contend with damaged pipework in the past you are aware of where the worst spots are. If they are in your basement or another room, you can simply warm the room. This may not be the best option to save you money on electricity but it’ll stop the pipes from breaking.
  • The area that is heated surrounding the frozen area by hand. If you do not want to warm the entire area, simply observe the temperature and then make a decision only when it becomes too cold. Plan regular visits to your pipes , and warm them up when you spot any indication of frozen ice.
  • Use a temperature-controlled thermal convection powered hot water recirculation valve. It doesn’t require electricity to function. It simply circulates warm water between the cold and hot lines of water when the temperature drops below a specific point. The drawback of this technique is that it requires that the valve be installed at least two levels above the heater. In addition, your water bill will rise significantly.

Cleaning your home’s plumbing in the winter is a serious job and, often the knowledge you have might not be sufficient. This is why it’s important to perform a complete inspection each year, and spot the issues before they become.

How to Fix a Broken Pipe Inside a Wall

Repairing a leak in a wall isn’t an straightforward task, and it’s best to have professionals handle this. If you’re confident that you’re able to do this yourself, simply follow these steps.

  • Cut off sections of damaged wall using a saw. When you’re sure exactly where the issue is Cut the wall to be able to access it.
  • Wrap a sheet of paper around the pipe and move it around until the sheet is damp. If you don’t be able to spot the damage through your eyes You’ll have to locate it using a piece cloth. It may be necessary repeat this several times until you find exactly where the breakage.
  • Set up a container beneath the pipe that is broken. The plumbing repair is messy, and the container must be able to hold any spills that come out of the pipe that you’re about to fix.
  • Cutting the pipes just below where the pipe leaks. It is necessary to use an instrument for cutting pipes to accomplish this. The tool is screwed tightly and then rotate it until the pipe is cut.
  • The pipe should be dried. It’s not possible to work when it’s damp.
  • Cut through the leak using another pipe cutter.
  • Clear the pipes. This applies to both the exterior and the interior. The inside could be more ice-laden therefore make sure that it’s free of any obstructions.
  • Install a copper repair sleeves. Use a blowtorch to warm the bottom of the repair sleeves. Let the solder get melted, filling the joint. When it is cool, around 10 minutes, repeat exactly the same thing for the upper part. Wear safety glasses and gloves during this process. Check for leaks after you’re done.
  • Repair the walls.